Skip to content

Version 3.4.0 ​

19. November 2026

Added ​

  • App/UI: A search field above long lists: in zones with six rooms or more for the zone's rooms and devices, on the devices page from ten devices on by name, room or type. On a smartphone it appears when the list is pulled down
  • App/UI: The floor plan now on the smartphone too, zoomed with two fingers or a double tap. Zoomed all the way out, a zone shows each room with its name and status; a tap zooms in to its switches
  • Backend: New KNX device types: presence detector, smart meter, valve, door lock and RGB(W) with color temperature. Door, room controller and other types previously only available as addons are now included directly
  • Backend: Vehicles: new APIs initVehicleAuthorization and getVehicleAccountVehicles (administrators only)
  • Backend: SFTP access: new APIs getSftpAccess, startSftpAccess and stopSftpAccess (administrators only)
  • Backend: Add-ons: new APIs updateAddonProfile and getAddonProfileUpdates (administrators only)
  • Backend: Notifications: push and e-mail recipients can be people: user:<uid>, group:admin and group:all, resolved when sending. setNotificationProfile removes a channel passed as null
  • Backend: Notifications: system notifications for smoke, water, low battery and malfunction. Devices that report these values (among them smoke and water detectors, heat pumps, wallboxes and inverters) raise their system profile by themselves. Out of the box as a log entry; smoke and water also by push to every device, a malfunction by push to the administrators
  • Backend: New add-ons for water and building services: SYR SafeTech Connect and Hansgrohe Pontos (including the older V3/V4 and Pontos Base), JUDO i-soft SAFE+ and ZEWA i-SAFE, uninterruptible power supplies through Network UPS Tools (APC, Eaton and others) and the OpenSprinkler irrigation controller
  • Backend: New add-on for the OpenTherm Gateway (OTGW): boiler and thermostat values of any OpenTherm heating system, with room setpoint, hot water mode and hot water setpoint writable
  • Backend: New add-on for Akuvox door stations: door opener, relay and input states, door bell and call
  • Backend: New add-ons for heating and air conditioning: Buderus, Bosch and Junkers through EMS-ESP, Vaillant through ebusd (read only), Panasonic Aquarea through HeishaMon, Daikin Altherma and ROTEX through ESPAltherma, Wolf boilers through ebusd (read only), Dimplex heat pumps (WPM, which also covers Weishaupt WWP LA/SLW/BA), Daikin air conditioners with the BRP069 Wi-Fi adapter, and RESOL solar thermal controllers through DL2/DL3 as well as KM2 and DL2 Plus
  • Backend: New add-ons for power and charging: SENEC.Home V2.1/V3, SolaX X1/X3 Hybrid G4, Growatt MIN and TL-X, OpenDTU for Hoymiles modules, cFos Power Brain, Tesla Wall Connector Gen 3 (read only) and openWB 2.x
  • Backend: New add-on for Easee wallboxes: status, power, charging current, energy of the session and in total, the current limit, and in plain words why it is not charging; pausing and resuming the charge and the current limit can be set. A Node-RED flow from the profile's help page makes the connection
  • Backend: New add-on for FRITZ!DECT radiator thermostats (301, 302 and Comet DECT): temperature, setpoint, battery, open-window detection, boost and faults; setpoint, on/off and boost can be set. A Node-RED flow talks to the FRITZ!Box, and the profile's help page carries it
  • Backend: New add-on for dynamic electricity tariffs: the current exchange price, a price level, the day's best price and a flag telling whether electricity is cheap right now — so automations can move loads into the cheap hours. A Node-RED flow supplies the prices; two ready-made flows are on the profile's help page
  • Backend: New add-ons for lighting: WiZ, Yeelight, Govee (over its LAN interface, one lamp per controller) and Nanoleaf (Light Panels, Shapes, Canvas)
  • Backend: New add-ons for multimedia: NAD AV receivers over their RS232 protocol, BenQ and Optoma projectors, Bose SoundTouch, Kodi, Volumio, Lyrion (formerly Logitech Media Server) and the WyreStorm H2X and Blustream CMX88 HDMI matrices
  • Backend: New add-ons for sensors and environment: Davis WeatherLink Live and Ecowitt weather stations, Awair Element and Omni air quality monitors, and Reolink cameras as motion, person and vehicle detectors
  • Backend: New add-ons for household and shading: robot vacuums running Valetudo (Roborock, Dreame) and Becker CentralControl
  • Config/UI: Add-ons: updates from the online library. The profile list shows when there is a newer version of a downloaded profile; one click, after a confirmation, updates the profile and right after it the devices that use it. Importing or uploading a profile again replaces it instead of adding a copy. If the profile was changed in the profile editor, the configuration asks first: replace it or keep it as a copy. If the new version drops values that automations, scenes or tiles may use, it lists them before the update
  • Config/UI: Vehicles: Volvo as a further brand. You connect a Volvo with your Volvo account and pick your vehicle from its list. State of charge, range, fuel level, doors, windows, mileage and position are available; locking, unlocking and the climate control can be operated as far as the vehicle offers it. The authorisation lasts six months; more than seven days without a query also calls for a new sign-in
  • Config/UI: Vehicles: Tesla as a further brand. You connect a Tesla with your Tesla account, also with an account the owner has invited as a driver, and pick your vehicle from its list. State of charge, range, charging state, locking, doors, windows, trunk, mileage and position are available; commands are not supported. The controller never wakes the vehicle: while it is asleep, it shows the state the vehicle reported last, without position, mileage and windows. The authorisation lasts six months
  • Config/UI: SFTP access under Administration → Advanced → Tools: opens the project folder to an SFTP program such as FileZilla, with a password of your own or a generated one. Ends by itself after an hour and with every restart
  • Config/UI: Skills: a search in the device lists of every skill (so far only KNX and Add-ons). It finds devices by name, room and ID; for gateways and devices with channels (e.g. Shelly, Eltako, Wiser) also by the gateway's name, model, address or serial number
  • Config/UI: Notifications: recipients can now be people too: everyone, the administrators or single users. A notification reaches the devices the user is signed in on and their e-mail address, also after a change of phone, without touching the profile
  • Config/UI: Notifications: new Monitoring tab. Device monitoring, so far set up in the System Manager only, reports when devices stay unreachable longer than a chosen time, and when they are reachable again. It watches all devices, selected devices or whole platforms, with exceptions; recipients are people, devices and e-mail addresses, as in the notification profiles
  • Config/UI: Notifications: new System tab. The notifications the controller raises by itself (smoke, water, battery, malfunction, unusual behaviour, skill errors and warnings, controller connection, emergency mode, vacation mode) can be changed like notification profiles: channels, recipients and texts. Single devices can be excepted, and a profile can be reset to how it was delivered
  • Config/UI: Support VPN: When it is turned on, the configuration asks which partner gets remote access: nomos support ("nomos", prefilled) or an integrator by its partner ID. A new partner has to confirm the access first; until then the current partner keeps it. The page shows the state of the request, lets you change the partner or withdraw a waiting request, and reports when the support VPN certificate is being renewed or expires soon
  • Config/UI: When the Controller's clock is wrong (for example without internet right after setup), the sign-in page says so, and after signing in a notice leads to Settings → Apply System Time
  • Daemon: Commandserver: commands over HTTP/HTTPS can now send POST, PUT, DELETE and PATCH, each with its own body and content type — only GET was possible before

Changes ​

  • App/UI: Rooms and zones choose their view from a menu at the top right (All devices, By type, Floor plan)
  • App/UI: Overview: on a smartphone, pulling down opens the search
  • App/UI: When adding another Controller, "Cancel" leads back to the current one
  • Backend: Eltako skill tuned for the upcoming 2.6.0 gateway firmware and the series 14 devices (FSR14, FUD14, FSB14)
  • Backend: ETA add-on: target temperatures and operating modes can now be written as well
  • Backend: The backend starts faster and uses about 30 MB less memory
  • Backend: Node-RED now only starts if there are flows or when it is opened. This saves memory and speeds up the start
  • Backend: Notifications: when a user signs out on a device or is deleted, the device gets no more push notifications until a user signs in on it again. Disabled users receive no notifications
  • Backend: Notifications: emergency mode and the connection alert of connected controllers run through the new system profiles. The connection alert now goes to the administrators by push and e-mail instead of to every device and user
  • Backend: Notifications: errors and warnings of Home Connect, Miele, Spotify and vehicles run through the new system profile "Skill errors and warnings"; the same message reports at most every 15 minutes
  • Backend: Notifications: findings of the usage recording run through the new system profile "Unusual behaviour"; the switch and recipients from the advanced settings are taken over on the update
  • Backend: a yes/no value a device has never reported is null instead of false, among others in getComponentData
  • Backend: Security check: a missing monitoring is no longer a finding (CVE-24-0005 dropped)
  • Backend + Config/UI: Vacation mode: every switch reports through the new system profile "Vacation mode", so push and e-mail are possible too. The former switch for the log entry is taken over
  • Config/UI: Add-ons: the profile list shows how many devices use each profile and marks the unused ones. Deleting a profile that is still in use now names the devices to delete first instead of showing a general error
  • Config/UI: The outdated Project Editor has been removed, replaced by SFTP access
  • Config/UI: Notifications: log, push and e-mail are no longer separate kinds but channels of one profile. A profile has one shared title and text, its own per channel if needed. Automations offer all profiles in one selection. Existing profiles stay as they are and can be given more channels
  • Config/UI + Backend: Notifications: new channel Services. Profiles can now also send to Slack, Microsoft Teams, Discord, ntfy or a JSON webhook, straight from the controller. The services are set up under Notifications → Services
  • Config/UI + Backend: Notifications: new channel Telegram. People get messages through a Telegram bot of your own, set up under Notifications → Services as a new service; everyone links their Telegram in their own account with a link or QR code. Telegram groups can be picked as a service
  • NodeRED: Upgraded to version 5.0.10

Fixed ​

  • App/UI: Over a poor remote access connection the app connects faster
  • App/UI: iOS: When the app started over a poor remote access connection, the screen stayed white or black for up to five minutes and did not respond
  • App/UI: A room without a floor plan showed the floor plan of the room opened before
  • App/UI: After the screensaver's night dimming the display sometimes stayed dark instead of returning to its own brightness
  • App/UI: A Controller with a new IP address could not be added again: the app went back to the old address and reported it as not available
  • App/UI: Adding a signed-in Controller again signed the app out of it, remote access included
  • App/UI: Android: "Reset" and switching to another Controller often had no effect
  • App/UI: Removing another Controller in the settings made the app start on the first one in the list next time
  • App/UI: After an expired sign-in the Controller's name was missing from the list, and after logging out it could not be added cleanly any more
  • App/UI: Switching to remote access briefly showed "… is currently not available"
  • App/UI: A push notification for an unreachable Controller opened the room or device with the same number in the other Controller after switching back
  • Backend: MQTT devices that report their reachability as a word (Tasmota and others) appeared unreachable in the app although they were reachable
  • Backend: Add-ons: yes/no values computed from an expression returned intermediate results instead of 0 or 1, seen among others on the RESOL VBus
  • Backend: Add-ons: when the connection file of an add-on device could not be written, the device was created anyway and stayed silent. Creating it now stops with a message
  • Backend: go-eCharger add-on: the energy charged and the total energy show one decimal instead of whole kWh
  • Backend: Matter and Shelly blinds moved the wrong way when the slider was pulled all the way to 0 % or 100 %
  • Backend: Shelly: on some controllers devices could not be added; adding them ended in a timeout although the device was connected to nomos
  • Backend: Matter crashed repeatedly after startup in time zones west of UTC until the controller had synchronized its clock
  • Backend: More reliable restart of the backend through the API; it used to come back only after a delay
  • Backend: Add-ons: calling a device's webhook address could restart the backend
  • Backend: automations that react to a value of an HTTP, TCP/Modbus or UDP add-on, to a value reported via webhook, to the position, tilt or heating demand of a Zigbee device or to the reachability of a camera never ran. When a device's profile changes, its automations and scenes are now compiled again too, instead of running on the old version
  • Backend: Somfy: garage doors that TaHoma drives with an impulse command only could not be moved. Add doors that already exist once more
  • Backend: Husqvarna: if the sign-in timed out while connecting the account, the configuration was not told and kept waiting
  • Backend: Miele and Home Connect: when the event connection to the cloud was re-established, the old connection could close the new one and mark all appliances unreachable
  • Backend: Miele and Home Connect: when added, an appliance could get functions and consumption values of another appliance of the same type that it does not have itself. Miele also left out consumption values when the appliance does not measure one of them
  • Backend: Wiser: a device without a name on the gateway could restart the backend when the device list was requested
  • Backend: Zeptrion: an unreachable device received more requests with every failed attempt instead of one every 20 seconds. The device search could restart the backend if a device returned no channel description
  • Config/UI: Add-ons: the profile editor lost settings it does not show itself when saving, such as the formatting of values or grouped actions; negative value ranges became positive. A profile that devices use can now be saved; those devices take the change over at once
  • Config/UI: Spotify, Home Connect, Miele, Netatmo and Husqvarna: the browser could block the sign-in window without the page saying so
  • Config/UI: Settings → Units: the Pressure field was empty when the General tab had been open before
  • Config/UI: Smartphone and tablet: many pages were wider than the screen and cut off at the right
  • Config/UI: First-time setup: an administrator password shorter than 6 characters was not applied, and the Controller restarted with an empty password. The assistant now requires at least 6 characters and reports when the password could not be set
  • Daemon: Commandserver: response patterns find values more reliably; a pattern reaching past the end of the reply no longer delivers a wrong value but none. A command timeout NONE now applies to that command only
  • Daemon: Nuki: a lock that had charged once reported "charging" for good, and "not charging" cleared a critical battery
  • Daemon: General stability and performance optimizations